Compostion |
(Polymer coating ) |
|||||||
|
(Appearance) | Golden translucent | ||||||
Specification | ||||||||
|
|
For nylon fabric, mercerized cotton fabric, smooth fabrics. Flat screen, rotary screen, hand printing can be. | ||||||
Other Properties | Main Features | |||||||
|
|
This product is mainly used in the printing process are printed fabric fixed position. | ||||||
Range Of Use | ||||||||
Method Of Use |
First by adding the appropriate proportion washer water (generally 3:7, ie 30% of Taiwan plastic, 70 percent washer water), the full mix evenly rubbed in the printing stage, can wait until after the drying cloth spread on top, stick tight production. |
|||||||
Suggestions |
1 shop front desk plastic material must wait until dry cloth covered can go, otherwise it will cause Taiwan glued to the fabric caused by the end of viscose. (2) After rubbed some time, if tack fall, you can use a small amount of solvent to clean countertops can also be cleaned with detergent water table. 3 If you think the glue is too thick, you can use special solvent dilution, some solvents may not match, the dilution should be preceded by trials. |
|||||||
|
15KG | |||||||
Packing | ||||||||
储运 | This product is flammable and should be stored in a cool, well ventilated place, hug flammable storage requirements. | |||||||
Storage and Transportation | ||||||||
注意(Note) | The above data the Company laboratory validation of reliable data for reference purposes only, without any guarantee, please read carefully before use! After the relevant information and experimental confirmation before mass production. | |||||||
Material Safety Data Sheet
1. Product Identification
Product Name |
Rig along the United States on the 1st |
||
Chemical composition |
Polymer acrylate copolymers, ethyl acetate |
||
Formula |
—— |
Molecular Weight |
—— |
2. Physical Data
Boiling point(760mmHg)℃ |
~95 |
Freezing point ℃ |
~0 |
Relative density (water = 1,20 ℃) |
1.23±0.01 |
Vapor pressure (20 ℃) Kpa |
9.7 |
Vapor Density (Air = 1) |
<1 |
Solubility in water,% |
Water-insoluble |
Solid content,% |
40 |
Evaporation rate (butyl acetate = 1) |
<1 |
PH value |
5~6 |
||
Appearance and Odor |
Golden yellow transparent liquid with a slight odor |
3. Ingredients and composition information
Mixture |
A polymer of acrylic ester copolymer, ethyl acetate, tackifying resin |
|
Hazardous components |
Content,% |
CAS NO。 |
|
|
|
4. Combustion and explosion hazard data
Flash point ℃ |
—— |
Ignition temperature ℃ |
—— |
Upper explosive limit (V / V),% |
—— |
Lower explosive limit (V / V),% |
—— |
Fire and explosion |
Solvent-based systems, the product is flammable, easy to burn, the combustion products are carbon dioxide (CO2), carbon monoxide (CO) |
Fire-fighting measures |
Fire fighting foam extinguishing agent, dry powder extinguishing agent when burned |
1. Stability and reactivity
Stability |
Stable |
Materials to avoid |
—— |
Conditions to avoid |
Sunlight, freezing |
Hazardous Polymerization |
—— |
2. TOXICOLOGICAL INFORMATION
(1) Acute toxicity: Acute toxicity similar substances is low.
(2) Additional toxicological information: similar substances is very low acute toxicity.
3. First aid measures
(1) Skin contact: Remove contaminated clothing with detergent and water thoroughly washed skin.
(2) eye contact: opened eyelids, mobile water rinse, use eye drops or a doctor.
(3) Inhalation: Inhalation of product vapors will not cause harm.
(4) smoking: vomiting, seek medical attention.
4. ECOLOGICAL INFORMATION
(1) Ecotoxicology: on fish and water plants will not cause harm.
(2) Biodegradability: biodegradable.
5. Spill response
Collect spillage in drums and disposed of in an appropriate place, wash the residue with an organic solvent.
10. Handling and Storage
Click Save combustible standards for storage, storage products, avoid direct sunlight and low temperatures of fire.
11. Transport Information
Note fire. Package can not be tilted or upside down.